Polyjacking, also called foam jacking or foam leveling, lifts sunken concrete by injecting expanding polyurethane foam underneath it. It’s quick and tidy, and it costs more than the older mudjacking method. So the real question for most Illinois homeowners isn’t how it works. It’s whether the price makes sense for their slab.
This guide gives you real numbers, explains why quotes vary so much, and covers the limits that sales pitches tend to skip.
The Short Answer
- Polyjacking costs about $5 to $25 per square foot. Most homeowners land around $8 to $15, and Angi puts the average near $15.
- Mudjacking runs about $3 to $6 per square foot, so foam is often two to three times the price.
- Typical totals: about $800 to $2,500 for a 100 sq ft sidewalk, and $1,500 to $3,200 for a 200 sq ft section of driveway.
- Replacing a slab averages around $10 per square foot and climbs when demolition or hard access is involved.
Those figures come from Angi, HomeGuide and HomeAdvisor. To price your own slab, call Payless Insulation at (217) 304-2885 or request a free quote.
How Polyjacking Works
- A crew drills small holes, about 5/8 inch wide, through the sunken slab.
- Two liquid components are pumped under the slab, where they react and expand into rigid foam.
- The foam fills the void and pushes the slab up. Good crews inject in small stages and check the height with a level between each one.
- The holes are filled and patched.
The mudjacking mix weighs 100 pounds or more per cubic foot, but the foam only 2 to 4 pounds per cubic foot. It’s ready to walk or drive on in roughly 15 to 30 minutes. For a plain-language look at the older method, see our mudjacking page.
Polyjacking Cost by Project
| Project | Rough polyjacking cost |
| Sidewalk (about 100 sq ft) | $800 – $2,500 |
| Patio | About $10 per sq ft |
| Partial driveway (about 200 sq ft) | $1,500 – $3,200 |
| Full driveway (about 450 sq ft) | $3,200 – $7,500 |
| Basement or interior floor | Often near $20 per sq ft |
Sidewalk figures from HomeGuide, driveway figures from HomeAdvisor, and per-square-foot figures from Angi. Interior floors cost more because of access and precision.
For a side-by-side comparison with other methods, see our concrete lifting cost guide.
Why Polyjacking Prices Vary So Much
That $5 to $25 spread isn’t random. It comes down to a few things you can ask about:
- How much foam your slab needs. Foam is the expensive part. A slab that dropped half an inch uses a small amount. One that dropped four inches over a large area can use many times more, and the price climbs with it.
- Foam density. Slabs that carry heavy loads, like a garage floor or a driveway with trucks, may call for denser foam, which costs more.
- Job size. Small jobs cost more per square foot because the crew still has to haul and set up the same equipment. Many companies also have a minimum charge.
- Access. Tight yards, steps, and areas a rig can’t reach slow the work.
- Why the slab sank. If a void is large because water has been washing soil away, it takes more material, and the cause has to be fixed too.
- Labor. Labor is a large share of the bill, often 40% to 70% depending on the source.
- Finish work. Patching holes in decorative or stamped concrete takes extra care.
How quotes get calculated. Most contractors price per square foot, but some price per job or by the amount of foam used. Ask how your quote is built, because a $9 per square foot price and a flat $1,200 job price aren’t easy to compare unless you know the area and lift involved.
Polyjacking vs. Mudjacking vs. Replacement
| Polyjacking | Mudjacking | Replacement | |
| Cost | $5 – $25 per sq ft | $3 – $6 per sq ft | About $10 per sq ft or more |
| Weight added to soil | Very light | Heavy | None (new slab) |
| Ready to use | 15 to 30 minutes | Often 24 to 48 hours | Days to weeks |
| Hole size | About 5/8 inch | About 1 to 2 inches | Not applicable |
| Best for | Weak soil, quick turnaround, decorative slabs | Large voids on firm soil, tighter budgets | Broken or crumbling slabs |
Pick polyjacking when the soil is soft or has already failed once, you need to use the slab right away, the surface is decorative or stamped, or an earlier mudjacking repair settled again.
Pick mudjacking when the soil is firm, the voids are big and the budget is tight.
Pick replacement when the slab is badly cracked, broken or crumbling, because lifting a shattered slab only raises the pieces.
What Polyjacking Can’t Do (the Honest Part)
Most websites, including some competitors, make polyjacking sound like a permanent cure. It’s a good repair, but it has limits.
It doesn’t harden or fix the soil. Foam fills the empty space under the slab and compacts some of the soil beneath it, but it doesn’t turn weak soil into strong soil. If water keeps eroding the ground next to the foam, new voids can form beside it.
It doesn’t fix a sinking foundation. Polyjacking is for flatwork: driveways, sidewalks, patios, garage slabs and similar. If your house is settling, with cracked walls, sticking doors or a leaning chimney, you need a foundation specialist.
Nobody can promise “forever.” Cured foam doesn’t rot or wash out. Whether the repair holds depends on the ground, drainage and how well it was done.
It can over-lift. Foam keeps expanding after the injection stops. A crew that injects in small stages and measures as it goes avoids this. It’s one of the best reasons not to use DIY foam kits.
It may not fill every void. Foam can leave unsupported pockets, which contractors sometimes call “pancake” voids. Good crews use several injection points and check the result by tapping and re-measuring.
Heated slabs need special care. Tell your contractor if your slab has radiant heat tubing, electrical cables or buried lines, so they can avoid them when drilling.
Is Polyjacking Eco-Friendly?
You’ll see this claim a lot. Here’s the balanced version. Cured foam is generally considered stable and inert, and polyjacking creates much less waste and truck traffic than tearing out and re-pouring a slab. At the same time, it’s a petroleum-based plastic, so it’s not a “green” product in the way recycled materials are. Treat marketing claims with a little skepticism and ask about the specific product.
Fixing the Cause Comes First
A slab sinks because something removed or compressed the soil beneath it. In central Illinois, the usual suspects are downspouts that dump water by the slab, clay and silty soils that swell and shrink, freeze-thaw cycles, poor compaction after construction, and leaky pipes. Fix those and your lift will last. Ignore them and you’ll be back. Our post on why concrete sinks explains the common causes.
Winter and Timing in Illinois
Foam is more temperature-sensitive than slurry. It works when the ground isn’t frozen, but cold soil can soak up the heat the reaction needs, so crews preheat the materials. Once the ground freezes solid around a slab, foam can’t spread properly underneath it, and many contractors pause until it thaws. Fall is often a good window in central Illinois, before hard frost sets in. If a slab is a trip hazard in January, ask your contractor what’s realistic for your site and weather.
How to Compare Polyjacking Quotes
Ask each contractor:
- What foam are you using, and at what density?
- How is the price calculated (per square foot, per job, or by material used)?
- What’s the minimum charge?
- How do you control the lift? (small stages, level checks)
- What will you do if the slab over-lifts or doesn’t fill evenly?
- Do you clean up and seal the holes?
- What does the warranty cover, and does it exclude soil washout or drainage problems?
- What should I do about drainage so the repair lasts?
Be careful with a quote that promises it will last “forever” or one that’s far below every other bid.
Can I Do It Myself?
Canned DIY foam can technically lift a slab, but it isn’t made for it, and over-lifting is a real risk. Once a slab goes too high, you can’t bring it back down. A failed DIY lift can also make a pro repair harder and more expensive. For small jobs, better DIY steps are extending downspouts, regrading and sealing cracks.
Polyjacking FAQs
What is the cost per square foot of polyjacking? About $5 to $25, with many jobs around $8 to $15 and an average near $15.
Is polyjacking worth it? Often, yes on weak soil, decorative slabs, or when you need the slab back in use quickly. On firm soil with a large void, mudjacking can do the same job for less.
How long does polyjacking last? The foam itself doesn’t rot or wash away. The repair lasts as long as the soil under and around it stays stable, so fixing drainage matters.
How long does it take? Most residential jobs take a few hours. Usually, the slab can be used in 15 to 30 minutes.
Can polyjacking be done in winter? Sometimes. It works if the ground isn’t frozen, but it’s more temperature-sensitive than mudjacking.
Does polyjacking work on all concrete? It works well on intact or lightly cracked flatwork. It isn’t suited to crumbling slabs or sinking house foundations.
Is polyjacking cheaper than replacing concrete? Often, but not always. At the high end of the price range, foam can approach replacement cost.
Will you see the holes? The holes are about 5/8 inch wide and are filled and patched, so they’re much less noticeable than mudjacking holes.
Get a Price on Your Slab
Every slab and every yard is different. Payless Insulation can look at yours and give you a clear quote. Call (217) 304-2885 or request a free quote. We serve Champaign, Danville, Decatur, Bloomington, Lafayette, IN and nearby communities. Find out more about how we can help you concrete lifting.